Cordless Compound Miter Saw Equipped with Electric Brake 216 mm (8-1/2”) MODEL LSSOODZ 216 mm (8-112”) MODEL LSSOODWA / MODEL LSSOODWAE 216 mm (S-ll2
Socket wrench The socket wrench is stored as shown in the figure. When using the socket wrench, pull it out of the wrench holder. After using the so
Installing or removing saw blade CAUTION: *Always be sure that the tool is switched off and the battery cartridge is removed before installing or rem
To install the blade, mount it carefully onto the spindle, making sure that the direction of the arrow on the surface of the blade matches the direc
Dust bag The use of the dust bag makes cutting operations clean and dust collection easy. To attach the dust bag, fit the bag's entry p
Kerf board Left bevel cut Straight cut CAUTION: After changing the bevel angle, always readjust the kerf boards as described above. Maintaining maxim
Positioning for adjusting the miter angle The turn base turns up to 52" to the left and 52" to the right. Loosen the grip by turnin
1. Vertical vise The vertical vise can be installed in two positions on either the left or right side of the guide fence, or the holder assem- bly (o
3. Holders and holder assembly (optional accessories) The holders and the holder assembly can be installed on either side as a con- venient means
To prevent the switch trigger from being accidentally pulled, a lock-off button is pro- vided. To start the tool, press in the lock-off button and
2. Miter cutting 3. Bevel cutting Refer to the previously covered "Positioning for adjusting the miter angle". *At a left 45" bevel an
SPECIFICATIONS Model LS800D Blade diameter ... 2 16 mm (8- 112&quo
5. Cutting crown and cover moldings *Crown and cove moldings can be cut on a compound miter saw with the moldings laid flat on the turn base. *There a
When cutting crown and cove moldings, set the bevel angle and miter angle as indicated in the table (A) and position the moldings on the top surface o
Ceiling Compound Miter Saw Miter and Bevel Angle Settings - - 3 14513.7 146 13.3 147 12.9 11.0 10.7 10.3 122 123 124 125 126 127 22.5 18.8 22.1 1
Compound Miter Saw Miter and Bevel Angle Settings 64 65 66 Wall to Crown Molding Angle: 45 degrees 36.8 48.5 36.6 48.0 36.4 47.4 Wall I Bevel I Mit
6. Cutting repetitive lengths When cutting several pieces of stock to the same length, ranging from 220 mm (8-5/8") to 365 mm (14-3/8"), us
MAINTENANCE CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or main
Make sure that the pointer points to 0" I I II I Carefully square the side of the blade with the top surface of the turn base on the miter scale
Make sure that the pointer on the arm points to 0" on the bevel scale on the arm holder. If it does not point to 0", loosen the screw whic
Use a screwdriver to remove the brush holder caps. Take out the worn carbon brushes, insert the new ones and secure the brush holder caps.
ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other ac
For Your Own Safety Read Instruction Manual Before Operating Compound Miter Saw Save it for future reference GENERAL SAFETY PRECAUTIONS (For Al
- Set plate Part No. 122551-4 High Capacity Battery Charger Model DC1801 Vise assembly (horizontal vise) Part No. 122563-7 Holder assembly Part No. 19
Jan.-20-'2000 US 216 mm (8-1/2") CORDLESS COMPOUND MITER SAW Model LS800D Note: The switch and other part configurations may differ from
MACHINE 1 3 4 5 6 7 8 9 10 11 12 13 14 15 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52
MAKmA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to
16. REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is in off position before inserting battery. 17. USE RECOMMENDED ACCESSORIES. Consu
ADDITIONAL SAFETY RULES 1. Wear eye protection. 2. Do not operate saw without guards in place. 3. Don’t use the tool in the presence of flammable l
IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER & BATTERY CARTRIDGE 1. SAVE THESE INSTRUCTIONS - This manual contains important safety and operating
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OoF1 or ABOVE 4OoC
Installing or removing battery cartridge *Always switch off the tool before inser- tion or removal of the battery cartridge. *To remove the batt
When you charge a new battery cartridge or a battery cartridge which has not been used for a long period of time, it may not accept a full charge. Thi
Commentaires sur ces manuels