Makita BUB360 Manuel d'utilisateur télécharger pdf (Page 5)

follow the safety rules stated in this instruction

manual may cause serious personal injury.

IMPORTANT SAFETY

INSTRUCTIONS ENC007-6

FOR BATTERY CARTRIDGE

1. Before using battery cartridge, read all

instructions and cautionary markings on (1)

battery charger, (2) battery, and (3) product using

battery.

2. Do not disassemble battery cartridge.

3. If operating time has become excessively shorter,

stop operating immediately. It may result in a risk

of overheating, possible burns and even an

explosion.

4. If electrolyte gets into your eyes, rinse them out

with clear water and seek medical attention right

away. It may result in loss of your eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any

conductive material.

(2) Avoid storing battery cartridge in a container

with other metal objects such as nails, coins,

etc.

(3) Do not expose battery cartridge to water or

rain.

A battery short can cause a large current flow,

overheating, possible burns and even a

breakdown.

6. Do not store the tool and battery cartridge in

locations where the temperature may reach or

exceed 50°C (122°F).

7. Do not incinerate the battery cartridge even if it is

severely damaged or is completely worn out. The

battery cartridge can explode in a fire.

8. Be careful not to drop or strike battery.

9. Do not use a damaged battery.

SAVE THESE INSTRUCTIONS.

Tips for maintaining maximum battery life

1. Charge the battery cartridge before completely

discharged.

Always stop tool operation and charge the battery

cartridge when you notice less tool power.

2. Never recharge a fully charged battery cartridge.

Overcharging shortens the battery service life.

3. Charge the battery cartridge with room

temperature at 10°C - 40°C (50°F - 104°F). Let a hot

battery cartridge cool down before charging it.

FUNCTIONAL DESCRIPTION

CAUTION:

•Always be sure that the tool is switched off and the

battery cartridge is removed before adjusting or

checking function on the tool.

Installing or removing battery cartridge

CAUTION:

• Hold the tool and the battery cartridge firmly when

installing or removing battery cartridge. Failure to

hold the tool and the battery cartridge firmly may cause

them to slip off your hands and result in damage to the

tool and battery cartridge and a personal injury. (Fig. 1)

•Always switch off the tool before insertion or removal of

the battery cartridge.

•To remove the battery cartridge, withdraw it from the

tool while sliding the button on the front of the cartridge.

•To insert the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Always insert it all the way until it locks in

place with a little click. If you can see the red part on

the upper side of the button, it is not locked completely.

Insert it fully until the red part cannot be seen. If not, it

may accidentally fall out of the tool, causing injury to

you or someone around you.

•Do not use force when inserting the battery cartridge. If

the cartridge does not slide in easily, it is not being

inserted correctly.

Battery protection system

The battery cartridge is equipped with the protection

system, which automatically cuts off the output power for

its long service life.

The tool may stop during operation when the tool and/or

battery are placed under the following situation. This is

caused by the activation of protection system and does

not show the tool trouble.

•When the tool is overloaded:

At this time, press the “OFF” button and remove

causes of overload and then press the “HIGH/LOW”

button again to restart. When the tool does not work

even after pressing the “HIGH/LOW” button, the battery

power auto-stop is still at work. Charge the battery

cartridge before use.

•When the remaining battery capacity becomes low:

Recharge the battery cartridge.

Switch action (Fig. 2)

To start the tool, simply press the “HIGH/LOW” button. To

switch off, press the “OFF” button. To change the tool

speed, press the “HIGH/LOW” button. The first press on

this button is for high speed and the second press for low

speed and then each press on this button repeats the

high/low speed cycle alternatively.

Battery remaining capacity indicator (only

for models with Battery BL3622A)

Battery BL3622A is equipped with the battery remaining

capacity indicator. (Fig. 3)

Press the CHECK button to indicate the battery remaining

capacity. The indicator lamps will then light for approx.

three seconds.

1 2 3 4 5 6 7 8 9 10 ... 19 20

Commentaires sur ces manuels

Pas de commentaire

Makita BUB360 Manuel d'utilisateur Page 5

Commentaires sur ces manuels

Produits connexes et manuels pour Outils de jardin Makita BUB360