Makita MLS100 Manuel d'instructions télécharger pdf (Page 10)

Vertical vise

Fig.24

The vertical vise can be installed in two positions on

either the left or right side of the guide fence. Insert the

vise rod into the hole in the guide fence and tighten the

screw to secure the vise rod.

Position the vise arm according to the thickness and

shape of the workpiece and secure the vise arm by

tightening the screw. Make sure that no part of the tool

contacts the vise when lowering the handle all the way. If

some part contacts the vise, re-position the vise.

Press the workpiece flat against the guide fence and the

turn base. Position the workpiece at the desired cutting

position and secure it firmly by tightening the vise knob.

CAUTION:

• The workpiece must be secured firmly against the

turn base and guide fence with the vise during all

operations.

OPERATION

010852

CAUTION:

• Before use, be sure to release the handle from the

lowered position by pulling the stopper pin.

• Make sure the blade is not contacting the

workpiece, etc. before the switch is turned on.

• Do not apply excessive pressure on the handle

when cutting. Too much force may result in

overload of the motor and/or decreased cutting

efficiency. Push down handle with only as much

force as is necessary for smooth cutting and

without significant decrease in blade speed.

• Gently press down the handle to perform the cut. If

the handle is pressed down with force or if lateral

force is applied, the blade will vibrate and leave a

mark (saw mark) in the workpiece and the

precision of the cut will be impaired.

1. Press cutting

Fig.25

Secure the workpiece with the vise. Switch on the

tool without the blade making any contact and wait

until the blade attains full speed before lowering.

Then gently lower the handle to the fully lowered

position to cut the workpiece. When the cut is

completed, switch off the tool and WAIT UNTIL

THE BLADE HAS COME TO A COMPLETE STOP

before returning the blade to its fully elevated

position.

2. Miter cutting

Refer to the previously covered "Adjusting the

miter angle".

3. Bevel cut

Fig.26

Loosen the knob and tilt the saw blade to set the

bevel angle (Refer to the previously covered

"Adjusting the bevel angle"). Be sure to retighten

the knob firmly to secure the selected bevel angle

safely. Secure the workpiece with a vise. Switch on

the tool without the blade making any contact and

wait until the blade attains full speed. Then gently

lower the handle to the fully lowered position while

applying pressure in parallel with the blade. When

the cut is completed, switch off the tool and WAIT

UNTIL THE BLADE HAS COME TO A COMPLETE

STOP before returning the blade to its fully

elevated position.

CAUTION:

• Always be sure that the blade will move down to

bevel direction during a bevel cut. Keep hands out

of path of saw blade.

• During a bevel cut, it may create a condition

whereby the piece cut off will come to rest against

the side of the blade. If the blade is raised while the

blade is still rotating, this piece may be caught by

the blade, causing fragments to be scattered which

is dangerous. The blade should be raised ONLY

after the blade has come to a complete stop.

• When pressing the handle down, apply pressure

parallel to the blade. If the pressure is not parallel

to the blade during a cut, the angle of the blade

might be shifted and the precision of the cut will be

impaired.

4. Compound cutting

Compound cutting is the process in which a bevel

angle is made at the same time in which a miter

angle is being cut on a workpiece. Compound

cutting can be performed at angle shown in the

table.

Miter angle

Bevel angle

Left and Right 0 - 45

006366

When performing compound cutting, refer to

"Press cutting", "Miter cutting" and "Bevel cut"

explanations.

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 75 76

Commentaires sur ces manuels

Pas de commentaire

Makita MLS100 Manuel d'instructions Page 10

Commentaires sur ces manuels

Produits connexes et manuels pour Scies à onglets Makita MLS100