search

Makita UC 3000 Manuel d'utilisateur Page 16

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 38
  • Table des matières
  • MARQUE LIVRES
    • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 15
16
2 3
1
Replacing the saw chain
CAUTION: Use only chains and guide bars designed for
this saw (see the Extract from the spare parts list)!
Check the sprocket (A/1) before mounting a new chain.
The sprocket is located underneath the clutch drum (I/2).
CAUTION:
Worn out sprockets (B) may damage the new chain and must
therefore be replaced.
Do not attempt to replace the sprocket yourself. Sprocket
replacement requires special training and tools and must be
done at a MAKITA service center.
B
A
NOTE:
The carbon brush is very delicate, so be careful not to let it drop.
When taking it out, be sure to note the position it was
installed in, since each brush is run in with the rotor.
- Use the combination wrench to unscrew the cover (C/2),
and then pull out the brush (C/3).
- If the wear limit has not yet been reached, put the brush
back in the same position and screw the cover (C/2) back
on.
- Run the saw briefly (about a minute) so the brushes can
run in again.
C
Cause
no power supply,
cable defective
chain brake actuated
Mains fuse blown
Carbon brushes worn down
oil tank empty,
oil guide groove dirty
Brake band worn down
System
total
Carbon brushes
Oil tank, oil pump
Brake
Observation
electric motor does not function
low pulling power
no oil on the saw chain
Saw chain does not stop instantly
Malfunction
Chain saw does not work
insufficient performance
no chain lubrication
Chain brake
Troubleshooting
Inspecting and replacing
the carbon brushes
IMPORTANT:
Inspect the carbon brushes at regular intervals! A notch
on the brush shows the limit of wear.
To maintain product SAFETY and RELIABILITY, repairs, any other
maintenance or adjustment should be performed by MAKITA Authorized
or Factory Service Centers, always using MAKITA replacement parts.
Vue de la page 15
1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 37 38

Commentaires sur ces manuels

Pas de commentaire
Produits connexes et manuels pour Outil à essence Makita UC 3000
Outil à essence Makita DCS 341 Manuel d'utilisateur    (60 pages)
Outil à essence Makita UC4020A Manuel d'utilisateur       (120 pages)
Outil à essence Makita DCS642120 Manuel d'utilisateur   (13 pages)
Outil à essence Makita DCS34 Manuel d'utilisateur   (9 pages)
Outil à essence Makita UC4030A Manuel d'utilisateur   (5 pages)
Outil à essence Makita UC3020A Manuel d'utilisateur   (2 pages)
Outil à essence Makita SLIDE COMPOUND SAW LS0711Z Manuel d'utilisateur   (32 pages)
Outil à essence Makita DCS5200 Manuel d'utilisateur    (64 pages)
Outil à essence Makita UC120D Manuel d'utilisateur       (48 pages)
Outil à essence Makita GE MONOGRAM ZISP480DXSS Manuel d'utilisateur   (6 pages)
Outil à essence Makita UC4020A Manuel d'utilisateur   (24 pages)
Outil à essence Makita UC4030AP Manuel d'utilisateur   (24 pages)
Outil à essence Makita DCS4610-40 Manuel d'utilisateur   (28 pages)
  • Yost-vises MK Diamond Products Vulkan IFB Appliances Td-machine-products
  • Insignia Jeux de haut-parleurs GE Réfrigérateurs-congélateurs Apple Affichages LED Creek Audio Amplificateurs audio pour voitures Polar Kits de voiture
  • Sony D-NE319 Sony DSC-W610 Makita 4114S Vivotek FD7131 Aeg L51260TL
  • Casio QV-R200 Manuel de l'utilisateur Electrolux EI24RD10QS Schéma de câblage GE EFMR Fiche technique Asus A7N8X Deluxe Manuel de l'utilisateur