Table SawWith Electric BraKe210 mm (8-1/4")MODEL 2702XlMODEL 2702255 mm (10")MODEL 2703X1MODEL 2703iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
1.HandleAdjusting depth of cutThe depth of cut may be adjusted by turning the han-dle. Turn the handle clockwise to raise the blade orcounterclockwise
11. Arrow pointerAfter adjusting the positive stops, set the blade at 90 ° tothe table surface. Then adjust the arrow pointer so thatits right edge is
CAUTION:• Always grasp the striped portion of the wrench whentightening the hex bolts. If you tighten the hex boltswhile grasping the wrench further t
When operating the switch lever, it is convenient toview it through the window area in the table.CAUTION:• When not using the tool, remove the key and
120 mT1 300 Tim(2")I I6 ram (1/4") j _ 50ram (2")2 _ .___ /_ 300 mm (12")130 mm _(5") 5_Zr,_)m,_ 100 mm (4")9.5 mm (3/8&
11. No. 10 wood screws (long enoughto penetrate halfway into facing)1. CROSS CUTTING2. MITERING3. BEVEL CUTTING4. COMPOUND MITERING(ANGLES)1. Groove2.
Auxiliary wood facing (miter gauge)To prevent a long board from wobbling, fit the mitergauge with an auxiliary fence board. Fasten withbolts/nuts afte
3. Turn the tool on and gently feed the workpiece intothe blade along with the rip fence.(1) When the width of rip is 150 mm (6") and wider,caref
MAINTENANCE1. Limit mark1. Holder cap opener2. Brush holder capCAUTION:• Always be sure that the tool is switched off andunplugged before attempting t
ACCESSORIES1/8" 1/8" 1/16" 1/8" 1/8"CAUTION:• These accessories or attachments are recommendedfor use with your Makita tool s
SPECIFICATIONSMODEL Arborhole2702X12702_8"2703X12703Blade Cutting capacities Maximum dadodiameter 90 450 capacity210rnrn 68rnm 47mm(8-1/4")
Table insert(Part No. 317061-6)When cutting grooves 5/16% 3/8",7/16" or 1/2" use thistable insert instead of the standard table insert.
1 2 3NOTE:• When widths slightly greater than the above arerequired, fit the paper washers in between the insideand outside cutters to adjust the widt
221i -2• _ /#31. "C"Clarnps2, Facing board3, Featherboard4, Push stickFeatherboards are used to keep the workpiece in con-tact with the rip
1 31. Rabbet2. First cut3. Second cut1. Rubber cap2. Nut3. Leg4. Under stay5. Stay1. Bolt2. StandHow to perform rabbeting1. Remove blade guard.2. Atta
ACCESSORIESCAUTION:• These accessories or attachments are recommendedfor use with your Makita tool specified in this manual.The use of any other acces
IIoFirst-ClassPostageRequiredPost Office willnot deliverwithout p_operpostageMakita U.S.A., inc.14930 Northam StreetLa Mirada, CA 90638-5753Ul,l,ulh,u
Your answers to the following questions are appreciated.1, Th_ product was, purchased 1tom:[] Home Center [] Other (]Hardware/Lumber Store[]hdustrial
CE1-800-4-MAK]TARETAIN THIS PORTION FOR YOUR RECORDSALABAMA COLORADO LOUISIANA II EW 'CORK _OEP,'fO RiCO2365 Pelham Rat kway 1183c_ E 51st A
Some dust created by power sanding, sawing, grinding, drilling, and otherconstruction activities contains chemicals known to the State of Californiato
For Your Own Safety Read Instruction ManualBefore Operating Table SawSave it for future referenceGENERAL SAFETY PRECAUTIONS(For All Tools)1. KNOW YOUR
16.REDUCETHERISKOFUNINTENTIONALSTARTING.Makesureswitchisinoffpositionbeforepluggingin.17. USE RECOMMENDEDACCES-SORIES.Consulttheowner'smanualforr
ADDITIONAL SAFETY RULESDO NOT let comfort or familiarity with product (gained from repeated use) replace strictadherence to table saw safety rules. If
18.Donotperformanyoperationfreehand.Freehandmeansusingyourhandstosup-portorguidetheworkpiece,inlieuofaripfenceormitergauge.19.NEVERreacharoundor overs
ASSEMBLYThe tool is shipped from the factory with the saw bladeand blade guard not in the installed condition. Assembleas follows:CAUTION:• Always unp
31. Blade guard2. Spreader3. Antikickback pawl4. Pressure plate3 1 6 21. These two clearancesshould be equal2. Blade guard portion3. Blade4. Spreader5
459mm(18-1/16")334mm 1(13-1/8")1.Holediameter8mm(5/16")25mm(1"1.6mm(1/4")Std.washer2.No.10woodscrew40mm(1-1/2")rain.leng
Commentaires sur ces manuels