210 mm (8-114") MODEL 2702x1 255 mm (10") MODEL 2703x1 210 mm (8-114") MODEL 2702 255 mm (10") MODEL 2703 With Electric
After adjusting the positive stops, set the blade at 90" to the table surface. Then adjust the arrow pointer so that its right edge is al
CAUTION: Always grasp the striped portion of the wrench when tightening the hex bolts. If you tighten the hex bolts while grasping the wrench further
When operating the switch lever, it is con- venient to view it through the window area in the table. I CAUTION: When not using the tool, remove the ke
Push stick A push stick can be easily made from a piece of plywood 19 mm (3/4”) to 25 mm (1 ’7 thick. Make auxiliary fence from 9.5 mm (3/8”) and
Wood facing (rip fence) A wood facing should be used for opera- tions when the blade comes close to the rip fence. Wood facing for the rip fence
Use of miter gauge Slide the miter gauge into the thick grooves in the table. Loosen the knob on the gauge and align to desired angle (Oo to SO0). Bri
1. Adjust the depth of cut a bit higher than the thickness of the workpiece. 2. Position the rip fence to the desired width of rip and lock in p
Feed the workpiece by hand until the end is about 25 mm (I”) from the front edge of the table. Continue to feed using the push block on the top of
MAINTENANCE CAUTl ON: Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Cleaning Clea
ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool speci- fied in this manual. The use of any othe
For Your Own Safety Read Instruction Manual 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Before Operating Table Saw Save it for future reference GENER
Table insert (Part No. 317060.8 for Model 2702) (Part No. 31 70614 for Model 2703) When cutting grooves 5/16", 3/8", 7/16" or 1/2"
NOTE: When widths slightly greater than the above are required, fit the paper washers in between the inside and outside cutters to adjust
Featherboards are used to keep the workpiece in contact with the rip fence and table as shown, and to stop kickbacks. To install featherboards, proce
How to perform rabbeting 1. Remove blade guard. 2. Attach auxiliaw fence to rip fence for cuts that run the length of the stock. Facing shoul
Sub-Table set NOTE: A table saw stand is necessary for installing the sub-tables. Sub-table (R) Part No. 122559-8 Sub-table (L) Part No. 122560-3 Part
Apr-28-'98 US TABLE SAW 210 mm (8-1/4") Model 2702 255 mm (1 0") Model 2703 57 25
11 114 Note: The switch and other part configurations may differ from country to country. 27
MACHINE __ MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy tvrr, MilkiU 1001 15 thoroughly lnrpcctrd and tested before lravlng the laclory It 17 vari
19. CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will
ADDITIONAL SAFETY RULES 1. Wear eye protection. 2. Don't use the tool in presence of flammable liquids or gases. 3. Never use the tool with a
17. Avoid abrupt, fast feeding. Feed as slowly as possible when cutting hard workpieces. Do not bend or twist workpiece while feeding. If you stall o
ASSEMBLY The tool is shipped from the factory with the saw blade and blade guard not in the installed condition. Assemble as follows: CAUTION: Always
Installing blade guard CAUTION: Before installing the blade guard, adjust the depth of cut to its maximum elevation. Insert the spreader between t
Locate the table saw in a well lit and level area where you can maintain good footing and balance. It should be installed in an area that lea
Adjusting depth of cut I The depth of cut may be adjusted by turn- ing the handle. Turn the handle clockwise to raise the blade or counterclockw
Commentaires sur ces manuels