1 INSTRUCTION MANUAL MANUEL D'INSTRUCTION MANUAL DE INSTRUCCIONES DOUBLE INSULATION DOUBLE ISOLATION DOBLE AISLAMIENTO WARNING: For your pers
10 Tableau 1. Gabarit minimum du cordonIntensité nominaleVolts Longueur totale du cordon en pieds120 V 25 pi 50 pi 100 pi 150 piPlus de Pas plus de Ca
11 l’ouvrage ou d’un accessoire brisé soient propulsés et provoquent des blessures hors de la zone immédiate de fonctionnement. 10. Tenez l'outi
12 maintenir à l'écart de tout produit inflammable. 25. N'abandonnez pas l'outil alors qu'il tourne. Ne faites fonctionner l&apos
13 Pour arrêter l'outil alors qu'il est en position verrouillée, tirez à fond sur la gâchette puis relâchez-la. ASSEMBLAGE ATTENTION: • A
14 ACCESSOIRES ATTENTION: • Ces accessoires ou pièces complémentaires sont recommandés pour l'utilisation avec l'outil Makita spécifié dan
15 ESPAÑOL ESPECIFICACIONES Modelo GV5010 GV6010 Especificaciones eléctricas en México 120 V 3,9 A 50/60 Hz Diámetro del disco abrasivo 125 mm (5
16 11. Evite el encendido accidental de la herramienta. Asegúrese de que el interruptor se encuentra en posición de apagado (OFF) antes de conectar l
17 Tabla 1. Calibre mínimo para el cableVoltios Longitud total del cable en metros120 V~7,6 m (25 ft) 15,2 m (50 ft) 30,4 m (100 ft) 45,7 m (150 ft)M
18 9. Mantenga a las personas alrededor a una distancia segura y apartada del área de trabajo. Cualquiera que ingrese al área de trabajo debe usar eq
19 ocasiona heridas personales. 21. Sostenga la herramienta con firmeza. 22. Mantenga las manos alejadas de las piezas giratorias. 23. Asegúrese de
2 ENGLISH SPECIFICATIONS Model GV5010 GV6010 Abrasive disc diameter 125 mm (5") 150 mm (6") No load speed (RPM) 4,500/min. Overall length
20 • El interruptor puede ser bloqueado en la posición "ON" (encendido) para mayor comodidad del operario durante una utilización prolongad
21 Para mantener la SEGURIDAD y FIABILIDAD del producto, las reparaciones, la inspección y sustitución de las escobillas de carbón, y cualquier otro m
23
24 Some dust created by power sanding, sawing, grinding, drilling, and otherconstruction activities contains chemicals known to the State of Californi
3 must be repaired. 18. Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing
4 6. The arbour size of backing pads or any other accessory must properly fit the spindle of the power tool. Accessories with arbour holes that do no
5 20. NEVER use tool with wood cutting blades or other sawblades. Such blades when used on a sander frequently kick and cause loss of control leading
6 ASSEMBLY CAUTION: • Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. Installing side grip (au
7 MAKITA LIMITED ONE YEAR WARRANTYWarranty PolicyEvery Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to b
8 FRANÇAIS SPÉCIFICATIONS Modèle GV5010 GV6010 Diamètre du disque abrasif 125 mm (5") 150 mm (6") Vitesse à vide (T/MIN) 4,500/min Longue
9 12. Retirez toute clé de réglage ou de serrage avant de mettre l'outil sous tension. Toute clé laissée en place sur une pièce rotative de l&ap
Commentaires sur ces manuels