Makita 4350T Manuel d'utilisateur télécharger pdf (Page 8)

(2) Apply pressure to the tool so that the front

edge of the base will not move when you

switch on the tool and gently lower the back

end of the tool slowly.

(3) As the blade pierces the workpiece, slowly

lower the base of the tool down onto the

workpiece surface.

(4) Complete the cut in the normal manner.

Finishing edges

Fig.15

To trim edges or make dimensional adjustments, run the

blade lightly along the cut edges.

Metal cutting

Always use a suitable coolant (cutting oil) when cutting

metal. Failure to do so will cause significant blade wear.

The underside of the workpiece can be greased instead

of using a coolant.

Dust extraction

Fig.16

Fig.17

The dust nozzle (accessory) is recommended to perform

clean cutting operations.

To attach the dust nozzle on the tool, insert the hook of

dust nozzle into the hole in the base.

The dust nozzle can be installed on either left or right

side of the base.

Then connect a Makita vacuum cleaner to the dust

nozzle.

Fig.18

CAUTION:

• If you try to remove the dust nozzle forcibly, the

hook of the dust nozzle can be diminished and

removed unintentionally during operation.

Rip fence set (optional accessory)

CAUTION:

• Always be sure that the tool is switched off and

unplugged before installing or removing

accessories.

1. Straight cuts

Fig.19

Fig.20

When repeatedly cutting widths of 160 mm or less, use

of the rip fence will assure fast, clean, straight cuts. To

install, insert the rip fence into the rectangular hole on

the side of the tool base with the fence guide facing

down. Slide the rip fence to the desired cutting width

position, then tighten the bolt to secure it.

2. Circular cuts

Fig.21

Fig.22

When cutting circles or arcs of 170 mm or less in

radius, install the rip fence as follows.

Insert the rip fence into the rectangular hole on the

side of the base with the fence guide facing up.

Insert the circular guide pin through either of the

two holes on the fence guide. Screw the threaded

knob onto the pin to secure the pin.

Now slide the rip fence to the desired cutting radius,

and tighten the bolt to secure it in place. Then

move the base all the way forward.

NOTE:

• Always use blades No. B-17, B-18, B-26 or B-27

when cutting circles or arcs.

Guide rail adapter set (accessory)

Fig.23

When cutting parallel and uniform width or cutting

straight, the use of the guide rail and the guide rail

adapter will assure the production of fast and clean cuts.

To install the guide rail adapter, insert the rule bar into

the square hole of the base as far as it goes. Secure the

bolt with the hex wrench securely.

Fig.24

Install the guide rail adapter on the rail of the guide rail.

Insert the rule bar into the square hole of the guide rail

adapter. Put the base to the side of the guide rail, and

secure the bolt securely.

Fig.25

CAUTION:

• Always use blades No. B-8, B-13, B-16, B-17 or 58

when using the guide rail and the guide rail

adapter.

Cover plate

Fig.26

Use the cover plate when cutting decorative veneers,

plastics, etc. It protects sensitive or delicate surfaces

from damage. Fit it on the back of the tool base.

Anti-splintering device

Fig.27

For splinter-free cuts, the anti-splintering device can be

used. To install the anti-splintering device, move the tool

base all the way forward and fit it from the back of tool

base. When you use the cover plate, install the

anti-splintering device onto the cover plate.

CAUTION:

• The anti-splintering device cannot be used when

making bevel cuts.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and

unplugged before attempting to perform inspection

or maintenance.

To maintain product SAFETY and RELIABILITY, repairs,

carbon brush inspection and replacement, any other

maintenance or adjustment should be performed by

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 51 52

Commentaires sur ces manuels

Pas de commentaire

Makita 4350T Manuel d'utilisateur Page 8

Commentaires sur ces manuels

Produits connexes et manuels pour Scies à chaîne sans fil Makita 4350T