Makita EA7900P Manuel d'instructions

Instruction ManualOriginal Instruction ManualImportant: Read this instruction manual carefully before putting the chain saw into operation and strictl

1057645123Lift the chain (6) over the sprocket (5). Using your right hand, guide the chain into the top guide groove on the guide bar (7).CAUTION:Note

119 10213311126 8Guide the chain over the chain catch (9).Pull the guide bar as shown by the arrow to take the slack out of the chain, so that it come

12STOP213121Checking the chain tensionThe tension of the chain is correct if the chain rests against the bottom side of the guide bar and can still be

13Gasoline+ 1000 cm3 (1 litre) 20 cm3 20 cm3 5000 cm3 (5 litres) 100 cm3 100 cm310000 cm3 (10 litres) 200 cm3 200 cm3 Chain oilUse an oil with a

14 RefuellingFOLLOW THE SAFETY PRECAUTIONS!Be careful and cautious when handling fuels.The engine must be switched off!Thoroughly clean the area aroun

1523Checking the chain lubricationNever work with the chain saw without sufÞ cient chain lubri -ca-tion. Otherwise the service life of the chain and

16Starting the engineStart the chain saw only after having assembled it com-pletely and inspected.Move at least 3m away from the place where you fuell

17Adjusting the carburetorCAUTION: Carburetor adjustment may only be done by a specialist MAKITA service centre! Only adjusting screw (S) can be manip

18BWorking in winterIn order to prevent carburetor icing in conditions of low tempera-ture combined with high humidity, and below + 5°C in order to ge

19MAINTENANCESharpening the saw chainCAUTION: Before doing any work on the guide bar or chain, always switch off the engine and pull the plug cap off

2Thank you for purchasing a MAKITA product!Congratulations on choosing a MAKITA chain saw! We are conÞ dent that you will be satisÞ ed with this moder

201 2Files and how to work with themSharpen using a special Þ le holder with a saw chain round Þ le. Normal round Þ les are not appropriate for this w

21516 72 348101175Cleaning the brake band and sprocket interiorCAUTION: Before doing any work on the guide bar or chain, always switch off the engine

2217CReplacing the suction headThe felt Þ lter (17) of the suction head can become clogged. It is recommended to replace the suction head once every

23CAUTION: To prevent eye injury, always wear eye protection when cleaning the Þ lter with compressed air!Do not use fuel to clean the air Þ lter.Unho

241078960,5 mmReplacing the spark plugCAUTION:Do not touch the spark plug or plug cap if the engine is running (high voltage).Switch off the engine be

2511Replacing the starter cable /Replacing the return springUnscrew three screws (1).Remove fan housing (2).NOTE: The screws (1) are secured against f

2618191315161417Mounting the fan housingPut the fan housing (13) on.Press the screws (14) into their holes.Lift the engine hood (15) slightly and use

27Instructions for periodic maintenanceTo ensure long life, prevent damage and ensure the full functioning of the safety features the following mainte

28Spare partsReliable long-term operation, as well as the safety of your chain saw, depend among other things on the quality of the spare parts used.

29Extract from the spare parts list Use only original MAKITA parts. For repairs and replacement of other parts, see your MAKITA service centre.P

314567328Delivery inventory1. Chain saw2. Guide bar3. Saw chain4. Chain protection cover5. Universal wrench6. Offset screwdriver7. Screwdriver for car

30EU Conformity DeclarationThe undersigned, Tomoyasu Kato, as authorized by MAKITA Corporation, declare that the MAKITA machines,Typ: 038, 039 Chain

31

Form: 995 707 581 (2012-06 GB)SpeciÞ cations subject to change without noticeTo Þ nd your local distributor, please visit www.makita-outdoor.com M

445671231432SAFETY PRECAUTIONSIntended usePower chain sawsThis power chain saw may be used only for sawing wood out of doors. It is intended for the f

565798Fuels / Refuelling- Stop the engine before refuelling the chain saw. - Do not smoke or work near open Þ res (5).- Let the engine cool down be

6ZKickback - When working with the chain saw dangerous kickbacks may occur.- Kickback occurs when the upper part of the end of the guide bar inadve

7- Be careful when cutting splintery wood. Cut pieces of wood may be pulled along (risk of injuries).- When cutting with the upper edge of the guide

8SERVICETransport and storage- When changing your location during work switch off the chain saw and actuate the chain brake in order to prevent an in

9Denomination of components 1 Handle 2 Filter hood 3 Filter hood clip 4 Tubular handle 5 Hand guard (release for chain brake) 6 Mufß er 7 Spike