Makita BLS713 Manuel d'instructions télécharger pdf (Page 12)

3. If operating time has become excessively shorter,

stop operating immediately. It may result in a risk

of overheating, possible burns and even an

explosion.

4. If electrolyte gets into your eyes, rinse them out

with clear water and seek medical attention right

away. It may result in loss of your eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any

conductive material.

(2) Avoid storing battery cartridge in a container

with other metal objects such as nails, coins,

etc.

(3) Do not expose battery cartridge to water or

rain.

A battery short can cause a large current flow,

overheating, possible burns and even a

breakdown.

6. Do not store the tool and battery cartridge in

locations where the temperature may reach or

exceed 50°C (122°F).

7. Do not incinerate the battery cartridge even if it is

severely damaged or is completely worn out. The

battery cartridge can explode in a fire.

8. Be careful not to drop or strike battery.

9. Do not use a damaged battery.

SAVE THESE INSTRUCTIONS.

Tips for maintaining maximum battery life

1. Charge the battery cartridge before completely

discharged.

Always stop tool operation and charge the battery

cartridge when you notice less tool power.

2. Never recharge a fully charged battery cartridge.

Overcharging shortens the battery service life.

3. Charge the battery cartridge with room

temperature at 10°C - 40°C (50°F - 104°F). Let a hot

battery cartridge cool down before charging it.

4. Charge the battery cartridge once in every six

months if you do not use it for a long period of

time.

INSTALLATION

Bench mounting (Fig. 1)

When the tool is shipped, the handle is locked in the

lowered position by the stopper pin. Release the stopper

pin by simultaneously applying a slight downward

pressure on the handle and pulling the stopper pin.

WARNING:

• Ensure that the tool will not move on the

supporting surface. Movement of the miter saw on

the supporting surface while cutting may result in loss

of control and serious personal injury. (Fig. 2)

This tool should be bolted with two bolts to a level and

stable surface using the bolt holes provided in the tool’s

base. This will help prevent tipping and possible injury.

(Fig. 3)

Turn the adjusting bolt clockwise or counterclockwise so

that it comes into a contact with the floor surface to keep

the tool stable.

FUNCTIONAL DESCRIPTION

WARNING:

• Always be sure that the tool is switched off and the

battery cartridge is removed before adjusting or

checking the functions on the tool. Failure to switch

off and remove the battery cartridge may result in

serious personal injury from accidental start-up.

Installing or removing battery cartridge

(Fig. 4)

•Always switch off the tool before insertion or removal of

the battery cartridge.

•To remove the battery cartridge, withdraw it from the

tool while sliding the button on the front of the cartridge.

•To insert the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Always insert it all the way until it locks in

place with a little click. If you can see the red part on

the upper side of the button, it is not locked completely.

Insert it fully until the red part cannot be seen. If not, it

may accidentally fall out of the tool, causing injury to

you or someone around you.

•Do not use force when inserting the battery cartridge. If

the cartridge does not slide in easily, it is not being

inserted correctly.

Battery protection system (Lithium-ion

battery with star marking) (Fig. 5)

Lithium-ion batteries with a star marking are equipped

with a protection system. This system automatically cuts

off power to the tool to extend battery life.

The tool will automatically stop during operation if the tool

and/or battery are placed under one of the following

conditions:

•Overloaded:

The tool is operated in a manner that causes it to

draw an abnormally high current.

In this situation, release the trigger switch on the tool

and stop the application that caused the tool to

become overloaded. Then pull the trigger switch

again to restart.

If the tool does not start, the battery is overheated. In

this situation, let the battery cool before pulling the

trigger switch again.

•Low battery voltage:

The remaining battery capacity is too low and the tool

will not operate. In this situation, remove and

recharge the battery.

Blade guard

For all countries other than European countries

(Fig. 6)

When lowering the handle, the blade guard rises

automatically. The guard is spring loaded so it returns to

its original position when the cut is completed and the

handle is raised.

WARNING:

• Never defeat or remove the blade guard or the

spring which attaches to the guard. An exposed

blade as a result of defeated guarding may result in

serious personal injury during operation.

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 59 60

Commentaires sur ces manuels

Pas de commentaire

Makita BLS713 Manuel d'instructions Page 12

Commentaires sur ces manuels

Produits connexes et manuels pour Scies circulaires Makita BLS713