Makita 4604DW Manuel d'instructions télécharger pdf (Page 7)

ADDITIONAL SAFETY RULES FOR BATTERY-

POWERED PRUNING SHEARS

1. This machine is for pruning branches. Do not

use it for any job except that for which it is

intended.

2. Don’t use the machine or perform battery charg-

ing operations in the rain.

3. Don’t leave the machine in rain or wet locations.

4. Keep bystanders well away from your work area.

5. Be careful not to catch foreign matter between

the blades. If the blades are jammed with foreign

matter, immediately switch off the machine and

disconnect the battery from the machine. Then

remove the foreign matter from the blades.

6. Never hold the branch you are pruning with your

free hand. Keep your free hand away from the

cutting area. Never touch the blades, they are

very sharp and you may cut yourself.

7. Don’t force the machine to make it cut. You could

slip and injure yourself or cut something else

unintentionally.

8. Avoid cutting electrical wires that may be hid-

den.

9. Always check the blades carefully before opera-

tion.

10. Handle the blades with extreme care to prevent

cuts or injury from the blades.

11. Disconnect the battery from the machine after

each use and before attempting to perform

inspection or maintenance.

12. When not in use, always keep the machine in its

holster.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Charging (Fig. 1 & 2)

Charge the battery 4600 with the Makita charger

DC4600 before use. Plug the charger into the power

receptacle and connect the charging plug into the charg-

ing connector on the battery. Press the start button (red)

on the charger. The charging light will come on and

charging will begin. When the charging light goes out

after about one hour, the charging will be completed. If

the charging light goes out within one minute after press-

ing the start button, the battery is dead. Replace it with a

new one. After charging, disconnect the charging plug

from the battery and power receptacle.

CAUTION:

• Remove the controller from the battery when charging.

• Do not keep the start button depressed with tape, etc.

The circuit will not function properly and a malfunction

of the charger may result.

• Use only Makita charger DC4600 to charge the battery

4600. The use of any other chargers may cause dam-

age to the battery.

• When you charge a new battery or a battery which has

not been used for a long period, it may not accept a full

charge. This is a normal condition and does not indi-

cate a problem. You can recharge the battery fully after

discharging it completely a couple of times.

Overcurrent relay (Fig. 2)

The overcurrent relay is built into the battery to prevent a

battery short-circuit. When the overcurrent relay actu-

ates, the battery cannot be used. Press the restart button

on the battery to use it again. If the overcurrent relay

actuates frequently, there may be something wrong with

the battery, charger, controller or shears themselves.

Send them to your dealer or a Makita Service Center to

have them inspected and/or repaired.

Installing controller on battery (Fig. 3 & 4)

First, make sure that the controller is switched off. Install

the controller on the battery and fasten it with the buck-

les.

Connecting connection cord to controller

Connect the male plug of the connection cord to the con-

troller connector and turn the screw clockwise to secure

the male plug in place.

Putting battery into waist belt pocket (Fig. 5 & 6)

After installing the controller on the battery, put the bat-

tery with the controller into your waist belt pocket so that

the controller connector will point toward your hand with

which you operate the shears. Then cover the battery

with the pocket lid to keep them from accidentally falling

out of your pocket during operation.

Wearing waist belt (Fig. 6)

Attach a pair of suspenders on the waist belt. Wear the

waist belt and adjust the lengh of suspenders and waist

belt so that the battery will be positioned on your back at

waist height.

Installing holster (Fig. 7)

Install the holster on the waist belt as shown in Fig. 7. It

should be positioned on the side where your hand oper-

ates the shears.

Wearing arm band (Fig. 8)

Attach the arm band to your arm. When wearing it, slip

the connection cord through the arm band as shown in

Fig. 8 to keep it out of the way.

Connecting connection cord to shears (Fig. 9)

Connect the female plug of the connection cord to the

shear connector and turn the screw clockwise to secure

the female plug in place.

NOTE:

If you connect or disconnect the connection cord with the

controller switched on, the pilot lamp will blink red and

green alternately. When this occurs, the shears will not

start even if you pull the switch trigger. Switch off the con-

troller and then switch it on again to start the shears.

(Fig. 4)

1 2 3 4 5 6 7 8 9 10 11 12 ... 18 19

Commentaires sur ces manuels

Pas de commentaire

Makita 4604DW Manuel d'instructions Page 7

Commentaires sur ces manuels

Produits connexes et manuels pour Outils électriques Makita 4604DW