EM2650UHEM2651UHEM2650LHEM2651LHPetrol BrushcutterEM2650UHEM2651UHEM2650LHEM2651LHINSTRUCTION MANUALImportant:Read this instruction manual carefully b
10CAUTION: Before doing any work on the Petrol Brushcutter, always stop the engine and pull the spark plug connector off the spark plug. Always wear
11To meet the applicable safety provisions, only the tool/ protector combinations as indicated in the table must be used.Be sure to use genuine MAKIT
12Turn the machine upside down, and you can replace the cutter blade or nylon cutting head easily.– Insert the hex wrench through the hole in the gea
13Inspection and rell of engine oil– Perform the following procedure, with the engine cooled down.– Set the engine level, remove oil cap (Fig. 1),
14REFUELINGHandling of fuelIt is necessary to handle fuel with utmost care. Fuel may contain substances similar to solvents. Refueling must be perform
15CORRECT HANDLING OF MACHINEAttachment of shoulder strap– Adjust the strap length so that the cutter blade will be kept parallel with the ground.For
163) Primer pump Continue to push the primer pump until fuel enters into the primer pump. (In general, fuel enters into the primer pump by 7 to 1
17CAUTION: The cutting tools mentioned below must only be resharpened by an authorized facility. Manual resharpening will result in imbalances of th
18CoverLatchesPressPress80 mm (3 - 1/8”) SpoolFor left hand rotationSpool100 mm (3 - 15/16”)NotchesEyeletsReplacing the nylon cord– First, stop the e
19CAUTION: Before doing any work on the Petrol Brushcutter, always stop the engine and pull the plug cap off the spark plug (see “checking the spark
2Thank you very much for purchasing the MAKITA Petrol Brushcutter. We are pleased to recommend to you the MAKITA Petrol Brushcutter which is the resul
20CLEANING OF AIR CLEANERDANGER: INFLAMMABLES STRICTLY PROHIBITEDInterval of Cleaning and Inspection: Daily (every 10 operating hours)– Turn the chok
21CLEANING OF FUEL FILTERWARNING: INFLAMMABLES STRICTLY PROHIBITEDInterval of Cleaning and Inspection: Monthly (every 50 operating hours)Suction head
22WARNING: When draining the fuel, be sure to stop the engine and conrm that the engine cools down. Just after stopping the engine, it may still hot
23*1 Perform initial replacement after 20h operation.*2 For the 200 operating hour inspection, request Authorized Service Agent or a machine shop.
24TROUBLESHOOTINGBefore making a request for repairs, check a trouble for yourself. If any abnormality is found, control your machine according to the
Makita CorporationAnjo, Aichi, Japan884951A229 www.makita.comALA
3General Instructions– To ensure correct operation, user has to read this instruction manual to make himself familiar with the handling of the Petrol
4Start the Petrol Brushcutter only in accordance with the instructions.– Do not use any other methods for starting the engine!– Use the Petrol Brush
5Method of operation– Only use the Petrol Brushcutter in good light and visibility. During the winter season beware of slippery or wet areas, ice and
6Never straighten or weld damaged cutting tools.– Operate the Petrol Brushcutter with as little noise and contamination as possible. In particular ch
7TECHNICAL DATA EM2650UH, EM2650LHModelEM2650UH EM2650LHBike handle Loop handleDimensions: length x width x height (without cutting blade) mm1,765 x
8TECHNICAL DATA EM2651UH, EM2651LHModelEM2651UH EM2651LHBike handle Loop handleDimensions: length x width x height (without cutting blade) mm1,765 x
9⑬⑭⑮④⑤⑰⑦⑨⑪⑩⑫⑯EM2650LHEM2651LHEM2650UHEM2651UH2221DESIGNATION OF PARTSGB DESIGNATION OF PARTS1 Fuel tank2 Rewind starter3 Air cleaner4 I-O switch (on/o
Commentaires sur ces manuels