Makita 6336D Spécifications télécharger pdf (Page 4)

ENGLISH

Explanation of general view

1 Button

2 Battery cartridge

3 Charging light

4 Battery charger

5Bit

6 Tighten

7Sleeve

8 Ring

9 Bit holder

10 Switch trigger

11 Reversing switch lever

12 A side

13 B side

14 Clockwise

15 Counterclockwise

16 Low speed

17 High speed

18 Speed change lever

19 Adjusting ring

20 Graduations

21 Drill marking

22 Pointer

23 Limit mark

24 Brush holder cap

25 Screwdriver

SAFETY INSTRUCTIONS

WARNING! When using battery operated tools basic

safety precautions, including the following, should

be followed to reduce the risk of fire, leaking batter-

ies and personal injury: Read these instructions

before operating this product and save these instruc-

tions.

For safe operation:

1. Keep work area clean

– Cluttered areas and benches invite injuries.

2. Consider the work environment

– Do not expose the tool to rain. Keep work area well

lit. Do not use tools in the presence of flammable

liquids or gases.

3. Keep children away

– Do not let visitors touch the tool. Keep visitors

away from work area.

4. Store batteries or idle tools

– When not in use, tools and batteries should be

stored separately in a dry, high or locked up place,

out of reach of children.

– Ensure that battery terminals cannot be shorted by

other metal parts such as screws, nails, etc.

5. Do not force the tool

– It will do the job better and safer at the rate for

which it was intended.

6. Use the right tool

– Do not force small tools or attachments to do the

job of a heavy duty tools. Do not use tools for pur-

poses not intended.

7. Dress properly

– Do not wear loose clothing or jewellery, they can

be caught in moving parts. Non-skid footwear is

recommended when working outdoors. Wear pro-

tecting hair covering to contain long hair.

8. Use protective equipment

– Use safety glasses and if the cutting operation is

dusty, a face or dust mask.

9. Connect dust extraction equipment

– If devices are provided for the connection of dust

extraction and collection ensure these are con-

nected and properly used.

10. Do not abuse the supply cord (if fitted)

– Never carry the tool by the cord or yank it to dis-

connect from the socket. Keep the cord away from

heat, oil and sharp edges.

11. Secure the work

– Use clamps or a vice to hold the work. It is safer

than using your hand and it frees both hands to

operate the tool.

12. Do not over-reach

– Keep proper footing and balance at all times.

13. Maintain tools with care

– Keep cutting tools sharp and clean for better and

safer performance. Follow instructions for lubrica-

tion and changing accessories. Inspect tool cords

periodically and if damaged have repaired by an

authorized service facility.

14. Disconnect tools

– Where the design permits, disconnect the tool

from its battery pack when not in use, before ser-

vicing and when changing accessories such as

blades, bits and cutters.

15. Remove adjusting keys and wrenches

– Form the habit of checking to see that keys and

adjusting wrenches are removed from the tool

before turning it on.

16. Avoid unintentional starting

– Do not carry the tool with a finger on the switch.

17. Stay alert

– Watch what you are doing. Use common sense.

Do not operate the tool when you are tired.

18. Check damaged parts

– Before further use of the tool, a guard or other part

that is damaged should be carefully checked to

determine that it will operate properly and perform

its intended function. Check for alignment of mov-

ing parts, free running of moving parts, breakage

of parts, mounting and any other condition that

may affect its operation. A guard or other part that

is damaged should be properly repaired or

replaced by an authorized service facility unless

otherwise indicated in this instruction manual.

Have defective switches replaced by an authorized

service facility. Do not use the tool if the switch

does not turn it on and off.

19. Warning

– The use of any accessory or attachment, other

than recommended in this instruction manual, may

present a risk of personal injury.

– Ensure that the battery pack is correct for the tool.

– Ensure that the outside surface of battery pack or

tool is clean and dry before plugging into charger.

– Ensure that batteries are charged using the cor-

rect charger recommended by the manufacturer.

Incorrect use may result in a risk of electric shock,

overheating or leakage of corrosive liquid from the

battery.

20. Have your tool repaired by a qualified person

– This tool is constructed in accordance with the rel-

evant safety requirements. Repairs should only be

carried out by qualified persons using original

spare parts, otherwise this may result in consider-

able danger to the user.

1 2 3 4 5 6 7 8

Commentaires sur ces manuels

Pas de commentaire

Makita 6336D Spécifications Page 4

Commentaires sur ces manuels

Produits connexes et manuels pour Perceuses électriques Makita 6336D