Makita 6336D Spécifications télécharger pdf (Page 7)

Installing or removing driver bit or drill bit

(Fig. 3 & 4)

Important:

Always be sure that the tool is switched off and the bat-

tery cartridge is removed before installing or removing

the bit.

Hold the ring and turn the sleeve counterclockwise to

open the chuck jaws. Place the bit in the chuck as far as it

will go. Hold the ring firmly and turn the sleeve clockwise

to tighten the chuck.

To remove the bit, hold the ring and turn the sleeve coun-

terclockwise. When not using the driver bit, keep it in the

bit holders. Bits 45 mm long can be kept there.

Switch action (Fig. 5)

CAUTION:

Before inserting the battery cartridge into the tool, always

check to see that the switch trigger actuates properly and

returns to the “OFF” position when released.

To start the tool, simply pull the trigger. Tool speed is

increased by increasing pressure on the trigger. Release

the trigger to stop.

Reversing switch action (Fig. 6)

CAUTION:

• Always check the direction of rotation before operation.

• Use the reversing switch only after the tool comes to a

complete stop. Changing the direction of rotation

before the tool stops may damage the tool.

• When not operating the tool, always set the reversing

switch lever to the neutral position.

This tool has a reversing switch to change the direction of

rotation. Depress the reversing switch lever from the A

side for clockwise rotation or from the B side for counter-

clockwise rotation. When the switch lever is in the neutral

position, the switch trigger cannot be pulled.

Speed change (Fig. 7)

To change the speed, first switch off the tool and then

slide the speed change lever to the “II” side for high

speed or “I” side for low speed. Be sure that the speed

change lever is set to the correct position before opera-

tion. Use the right speed for your job.

CAUTION:

• Always set the speed change lever fully to the correct

position. If you operate the tool with the speed change

lever positioned half-way between the “I” side and “II”

side, the tool may be damaged.

• Do not use the speed change lever while the tool is run-

ning. The tool may be damaged.

Adjusting the fastening torque (Fig. 8)

The fastening torque can be adjusted in 17 steps by turn-

ing the adjusting ring so that its graduations are aligned

with the pointer on the tool body. The fastening torque is

minimum when the number 1 is aligned with the pointer,

and maximum when the

A marking is aligned with the

pointer.

The clutch will slip at various torque levels when set at

the number 1 to 16. The clutch is designed not to slip at

the

marking. Before actual operation, drive a trial screw

into your material or a piece of duplicate material to

determine which torque level is required for a particular

application.

NOTE:

• The adjusting ring does not lock when the pointer is

positioned only half-way between the graduations.

• Do not operate the tool with the adjusting ring set

between the number 16 and the

A marking. The tool

may be damaged.

Screwdriving operation (Fig. 9)

Place the point of the driver bit in the screw head and

apply pressure to the tool. Start the tool slowly and then

increase the speed gradually. Release the trigger as

soon as the clutch cuts in.

NOTE:

• Make sure that the driver bit is inserted straight in the

screw head, or the screw and/or bit may be damaged.

• When driving wood screws, predrill pilot holes to make

driving easier and to prevent splitting of the workpiece.

See the chart below.

• If the tool is operated continuously until the battery car-

tridge has discharged, allow the tool to rest for 15 min-

utes before proceeding with a fresh battery.

Nominal diameter of

wood screw (mm)

Recommended size of

pilot hole (mm)

3.1 2.0–2.2

3.5 2.2–2.5

3.8 2.5–2.8

4.5 2.9–3.2

4.8 3.1–3.4

5.1 3.3–3.6

5.5 3.7–3.9

5.8 4.0–4.2

6.1 4.2–4.4

1 2 3 4 5 6 7 8

Commentaires sur ces manuels

Pas de commentaire

Makita 6336D Spécifications Page 7

Commentaires sur ces manuels

Produits connexes et manuels pour Perceuses électriques Makita 6336D