Makita DML801X1 Manuel d'utilisation et d'entretien télécharger pdf (Page 4)

were specially designed for your tool, for optimum

performance and safety of operation.

9. Causes and operator prevention of kickback;

− Kickback is a sudden reaction to a pinched,

bound or misaligned blade, causing an

uncontrolled tool to lift up and out of the

workpiece toward the operator.

− When the blade is pinched or bound tightly by

the kerf closing down, the blade stalls and the

motor reaction drives the unit rapidly back

toward the operator.

− If the blade becomes twisted or misaligned in

the cut, the teeth at the back edge of the

blade can dig into the top surface of the

workpiece causing the blade to climb out of

the kerf and jump back toward the operator.

Kickback is the result of tool misuse and/or

incorrect operating procedures or conditions and

can be avoided by taking proper precautions as

given below.

• Maintain a firm grip with both hands on the

tool and position your arms to resist

kickback forces. Position your body to

either side of the blade, but not in line with

the blade. Kickback could cause the tool to

jump backwards, but kickback forces can be

controlled by the operator, if proper

precautions are taken.

• When blade is binding, or when

interrupting a cut for any reason, release

the trigger and hold the tool motionless in

the material until the blade comes to a

complete stop. Never attempt to remove

the tool from the work or pull the tool

backward while the blade is in motion or

KICKBACK may occur. Investigate and take

corrective actions to eliminate the cause of

blade binding.

• When restarting a tool in the workpiece, center

the blade in the kerf and check that blade

teeth are not engaged into the material. If

blade is binding, it may walk up or kickback

from the workpiece as the tool is restarted.

• Support large panels to minimise the risk

of blade pinching and kickback. Large

panels tend to sag under their own weight.

Supports must be placed under the panel on

both sides, near the line of cut and near the

edge of the panel.

• Do not use dull or damaged blades.

Unsharpened or improperly set blades

produce narrow kerf causing excessive friction,

blade binding and kickback.

• Blade depth and bevel adjusting locking

levers must be tight and secure before

making cut. If blade adjustment shifts while

cutting, it may cause binding and kickback.

• Use extra caution when making a "plunge

cut" into existing walls or other blind areas.

The protruding blade may cut objects that can

cause kickback. For plunge cuts, retract lower

guard using retracting handle.

10. Check lower guard for proper closing before

each use. Do not operate the tool if lower

guard does not move freely and close instantly.

Never clamp or tie the lower guard into the

open position. If tool is accidentally dropped,

lower guard may be bent. Raise the lower guard

with the retracting lever and make sure it moves

freely and does not touch the blade or any other

part, in all angles and depths of cut.

To check lower guard, open lower guard by hand,

then release and watch guard closure. Also check

to see that retracting handle does not touch tool

housing. Leaving blade exposed is VERY

DANGEROUS and can lead to serious personal

injury.

11. Check the operation and condition of the lower

guard spring. If the guard and the spring are

not operating properly, they must be serviced

before use. Lower guard may operate sluggishly

due to damaged parts, gummy deposits, or a

buildup of debris.

12. Lower guard should be retracted manually

only for special cuts such as "plunge cuts"

and "compound cuts." Raise lower guard by

retracting handle and as soon as blade enters

the material, the lower guard must be released.

For all other sawing, the lower guard should

operate automatically.

13. Always observe that the lower guard is

covering the blade before placing tool down

on bench or floor. An unprotected, coasting

blade will cause the tool to walk backwards,

cutting whatever is in its path. Be aware of the

time it takes for the blade to stop after switch is

released.

14. Do not stop the blades by lateral pressure on

the blade.

15. DANGER:

Do not attempt to remove cut material when

blade is moving.

CAUTION: Blades coast after turn off.

16. Place the wider portion of the tool base on that

part of the workpiece which is solidly

supported, not on the section that will fall off

when the cut is made.

17. Never attempt to make a cut with the tool held

upside down in a vise. This is extremely

dangerous and can lead to serious accidents.

1 2 3 4 5 6 7 8 9 ... 31 32

Commentaires sur ces manuels

Pas de commentaire

Makita DML801X1 Manuel d'utilisation et d'entretien Page 4

Commentaires sur ces manuels

Produits connexes et manuels pour Outils électriques Makita DML801X1