Makita EM4251 Manuel d'instructions

Brush Cutter Decespugliatore Desbrozadora EM4250 EM4250 I@ English I ltaliano I Spanish RECEIVED FER 1 4 2000 Grass Trimmer Tagliabordi Corta bordes E

To meet the applicable safety provisions, only the tool/ protector combinations as indicated in the table must be used. Be sure to use genuine MAKITA

Turn the machine upside down, and you can replace the cutter blade easily. For EM4250, EM4251 -Insert the hex wrench through lhe hole in the gear cas

Inspection and Refill of Engine Oil -Perform the following procedure, with the engine cooled down. -While keeping the engine level, remove the oil g

(1) Keep the engine level, and detach the oil gauge. (2) Fill oil up to the edge of the oil refill port. (Refer lo Fig2 of the preceding page). Feed o

Attachment of shoulder strap -Adjust the strap length so that the culter blade will be kept parallel with the ground. Detachment For EM4251 -In an em

For machine with U Handle or Loop Handle 1) Set the 1-0 switch (1) to OPERATION. 2) Choke lever Close the choke lever. Choke opening: - Full closing i

B: Startup after warm-up operation 1) Push the primer pump repeatedly. 2) Keep the throttle lever at the Idling position. 3) Pull the recoil starter s

NYLON CUlTING HEAD The nylon cutting head is a dual string trimmer head capable of both automatic and bump i% feed mechanisms. The nylon cutting head

-Align the protrusion on the underside of the cover with the slots of the eyelets. Then push cover firmly Onto the housing to secure it. eaL Cover -

3) Place waste or paper near the oil refill port. or paper 4) Detach the oil gauge, and drain oil, tilting the main unit toward the oil refill PO&qu

Thank you very much for purchasing the MAKITA Brush Cuner/Grass trimmer. We are pleased to recommend to you the MAKITA Brush Cuner/Grass trimmer whic

CHECKING THE SPARK PLUG -Only use the supplied universal wrench lo remove or to install the spark -The gap belween the two electrodes of Ihe spark p

-When the machine Is in storage for a long time, drain fuel from the fuel tank and carburetor, as follows: Drain all fuel from the fuel tank. Dispos

Operating time Engine oil Eghtening Parts (bolt, nut) Fuel tank Throttle lever stop switch Cutting blade Low-speed rotation Air cleaner Ignition plug

TROUBLESHOOTING Failure to operate primer pump Vir lietl Pro MI s!rf ant TaG L Ne ' Push 7 lo 10 times. Clogged fuel filter Clean Before making a

.. ,.: 3. .i !:- . .:5. :I, , ! (i. :' ;'. 'E ?I :

Start the Brush Cutter/Grass trimmer only in accordance with the instructions. -Use the Brush CuWGrass trimmer and the tools only for such application

Method of Operation -Only use the Brush cutter/Grass trimmer in good light and visibility. During the winter season beware of slippery or wet areas,

Never straighten or weld damaged cutting tools. -Operate the Brush cutter/Grass trimmer with as little noise and contamination -Clean the Brush cutl

Model Dimensions : length x width x height (without cutting blade) mm Mass (without plastic guard and cutting blade) kg Volume (fuel tank) cm3 Volume

EM4250 Brush Cutter d 7 - ;B 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 20 21 24 25 - - DESIGNATION OF PARTS Fuel Tank Rewind Starter Air Cleaner 1-

c CAUTION: Before doing any work on the brush cutter, always stop the engine and pull the spark plug connector off the spark plug. Always wear protec